VTS II Series Firmware Version 1.1.4 Release Notes Dec 05, 2007 Copyright (c) 1998-2007, Sena Technologies, Inc. INTRODUCTION ============= These release notes describe new features added and bugs fixed since the firmware V1.1.1 release. ENHANCEMENTS ============== + Added an option "Use CLI authentication method for serial console access" + Added menu options for /bin/factory_reset script. + Added /etc/iproute2/setsbr.sh script file to be used when user wants to set two separate route information under two default gateways or two different public networks. + Added the ability for automatic enabling of SCP mode in ServerTech Power controller configuration. + Added the ability to see suspicious intruders in system log. + Added the ability to permit remote authentication to the CLI that does not require a local user. + Added the support for new Pin code and next token code mode in RSA SecurID authentication. + Added the support for instant Serial Parameter changes through SNMP. + Added an option for flushing serial buffer on closing TCP connection. + Added the support for dial-in modem secondary callback phone number. + Removed the DRAC option in service processor when the corresponding port is a serial port. BUG FIXES ========= - Fixed the problem in applying time zone configuration which is imported through the configuration management. - Fixed the problem with incorrect spacing in Portaccess Menu when port names are longer than expected. - Fixed the problem with allowing root access through a dropped modem call. - Fixed the problem with uploading files via tftp to the /usr2 directory. - Fixed the problem with setting SNMPv3 configuration using Auth/NoPriv. - Fixed the problem with setting Time via NTP server. - Fixed the problem with IP filtering for ports. - Fixed the problem with specifying a range of ports in IP filtering. - Fixed the problem with booting Passport under high loaded UDP traffics. - Fixed the problem in automatic system log backup on mounting. - Fixed the problem with changing port parameters through basic configuration menu in configmenu. - Fixed the problem with setting two different public networks for dual network interface. - Fixed the problem with setting factory default for SAMBA and NFS configuration. - Fixed the problem with displaying the correct gateway address if both Ethernet interfaces have dhcp enabled. - Fixed the problem with displaying the correct time stamp on system log. - Fixed the problem with updating configuration through tftp. - Fixed the problem in ADR alert. - Fixed the problem in "Allow client access to local network via PPP connection" option in PPP configuration. - Fixed the problem with adding power controller in configmenu. - Fixed the problem with changing the IP address under HTTPS - Fixed the problem with displaying messages in configmenu for fail/success of config exporting. - Removed the inappropriate error message when importing configurations. - Fixed the memory leak in network interface up and down. - Fixed the problem with connecting dual network interfaces separately. - Fixed the problem in using clustering if any slave and/or peer has the Port access menu disabled. - Fixed the problem in using Access lists when used in Peer to Peer config. - Fixed the problem with double echo in zterm/putty telnet connection to port access menu. - Fixed the problem with applying IP Filtering Rule.(Give the priority to ACCEPT RULE) - Fixed the problem in using PortReset through SNMP. - Fixed the problem in sending keepalive packet if protocol is RawTCP. - Fixed the problem in displaying correct CPU utilization through SNMP. - Fixed the problem in using User names greater than 30 characters. - Fixed the problem in using master authentication in clustering if the user name is greater then 19 characters. - Fixed the problem in keeping PC card configuration after system reboot. - Fixed the problem in accessing VTS II through VTS Manager after changing Network configuration. - Fixed the problem in connecting remote ports after system reboot. - Fixed the problem in calling a callback number in dialin-modem mode. - Fixed the performance issue while connecting device sends data continuously. - Fixed the problem with configuring remote power controller to make the remote port enabled by default. - Fixed the JTA hiding problem on connection page. - Fixed the problem with using different get/set community variables for ServerTech PDU. - Fixed the problem with using Power management configuration menu on Serial port configuration page for ServerTech PDU. - Fixed the problem with saving RFC1213 SNMP configurations through SNMP. - Fixed the problem with configuring 16th cascaded RPM unit. NOTES ============ * None. KNOWN BUGS ============ * None. REVISION HISTORY ================ 1.1.1 March 10, 2007 + Added the support for Server Tech Power Unit(Serial and Ethernet) + Added Basic configuration and Enhanced automatic configuration + Added Port Group and command to a port group (command to multiple ports) + Added Automatic login option for regular remote port + Added option for configurable JTA windows size + Added option for local SSH client instead of using JTA + Upgraded OpenSSH version to 4.5p1 + Upgraded net-snmpd version to 5.4 + Increased # of freeKVM connection(up to 8) + Added iLO/DRAC/SMASH-CLP support + Added USB wireless device support. + Added support for uploading certificate via Web UI + Added support NTP configuration through the DHCP server + Added xmodem support(Perl module) for firmware upgrade through serial port + Added LDAPs (Start TLS) support + Added Day options in Daylight Saving Time configuration + Added user name on system logs + Added User list synchronization in Clustering + Added SNMP OIDs for power outlet control + Added configurable option for login and a callback number change in Dial-in modem mode - Fixed the problem with running rc.user script in creating start script - Fixed the problem in changing passwd in SSH Port Access Menu - Fixed the problem with displaying CLI user on the send-msg list in Port Escape Menu - Fixed the SNMPD engine ID problem. (Generating a unique Engine ID based on the MAC address) - Fixed the problem in preloading JAVA Applet.(JAVA Applet will be preloaded after login) - Fixed the problem in getting correct processorUtilization value through SNMP - Fixed some bugs in v1.0.3 1.0.3 March 5, 2007 + First public release CONTACTS ========= Sena Technologies Inc. 210 Yangjae-dong, Seocho-gu Seoul, Korea 137-130 url: http://www.sena.com email: info@sena.com phone: +82-2-573-7772 fax: +82-2-573-7710 Technical support: email: support@sena.com phone: +82-2-573-5422