SD/ESD firmware, Manual, Conf_SW release note APR 21, 2009 Copyright (c) 1998-2009, Sena Technologies, Inc. INTRODUCTION ============= ENHANCEMENTS ============== BUG FIXES ========= KNOWN BUGS =========== REVISION HISTORY ================ v1b - embrase with each return message when issued INQ? or INFO? - parsing routine is replaced with the one results from genparse.exe - add timeout to BTSCAN - some minor fixes v1c - add battery low power detection timer - include security library witch support multiple device security v2a - move security library into application level - add S-registers - add command BTSCAN, BTCSD, BTFP, &V, Sn=, Sn? v2b - improve AT-command parsing routine - pin negative reply when the number of secured devices exceeds the limit - BTINFO now informs the number of secured devices - BTINQ now infroms the cod of inquired devices v2c - foced paring flag automatically reset only when ATD succeed. - improve sendOk/sendError when debug is off - move grand macro definition to external Makefile v2d - add command AT&F and share its handler with event of reset button - add command AT+BTSD? and AT+BTSEC - add command AT+BTLAST? v2e - modify linkkey storage to rotate - AT+BTSD? displays only the bd-addresses of secured devices - remove not-used enum definition from security.h v2f - config UART baudrate upto 921k - infinite timeout with mode 2 or 3 at handelATBTSCAN - fix bug of ignored initial frame size when connect as slave v2g - fix width of CoD at the result of inquiry - support paring without enabling authentication when connect as master v2h - support low speed UART (upto 1200bps) - enable SD messages by S-register ('OK','ERROR','CONNECT','DISCONNECT') v2i - enable 3 modem control line (DTR,DSR,CD) - this firmware supports sd202 and sd 102 v2j - rewrite device name initialization procedure - support full DTR transfer v3a - save error code - user configurable escape sequence character - command mode escaping can be disabled - change default frame size (to 270) - UART buffer clear on the event of disconnect - change connect message - increase the number of secured devices to 7 - correct ATO handling bug v3b - remove conn_status and current_state variable from gu_state - can set a factory initial S-register values - add BTINIT to save current S-register values - SCAN, ATD, BTMODE can be executed at pending status. - add H/W flow control setup option - 2004.01.27 increse the size of the inquiry scan window - optimize the library by eliminating unnecessary event v4a - Support Bluetooth 1.2 - Support DFU, AFH, Fast connection - S31 reset time, mode1 auto reconnect v4b - fixed the problem in CSR bug. v4c Parani-SD100 V1.0.0 - Support Bluetooth 1.2, DFU, AFH, at+btver?, pairing, faster connection V1.0.1(20061012) - add DCD On/Off option V1.0.2(20061027) - fixed the problem in CSR bug. V1.1.0(20070319) - add Intercharacter timeout. fixed the problem in toshiba driver bug. fixed the problem in Flowcontol bug. V1.1.1(20070530) - fixed the problem in intercharacter timout. add sniff low power mode. (S47~S52) add ACL connection. (ata) V1.1.2(20070912) - fixed the problem in DCD signal. V1.1.3(20080107) - add S45(iac), pairing iac V1.1.4(20080314) - fixed the problem in DCD signal. support 000b53 bd address. fixed the problem in 28 connection with MSP1000 and SDP response bug. V1.1.5(20080416) - fixed the problem in at+btcancel bug V1.1.6(20090310) - add pairing cod, remove pairing iac V1.1.7(20090323) - fixed the problem in DCD bug. Parani-SD200 V1.0.0 - Support Bluetooth 1.2, DFU, AFH, at+btver?, pairing, faster connection V1.0.1(20061012) - add DCD On/Off option V1.0.2(20061027) - fixed the problem in CSR bug. V1.1.0(20070319) - add Intercharacter timeout. fixed the problem in toshiba driver bug. fixed the problem in Flowcontol bug. V1.1.1(20070530) - fixed the problem in intercharacter timout. add sniff low power mode. (S47~S52) add ACL connection. (ata) V1.1.2(20070912) - fixed the problem in DCD signal. V1.1.3(20080107) - add S45(iac), pairing iac V1.1.4(20080314) - fixed the problem in DCD signal. support 000b53 bd address. fixed the problem in 28 connection with MSP1000 and SDP response bug. V1.1.5(20080416) - fixed the problem in at+btcancel bug V1.1.6(20090310) - add pairing cod, remove pairing iac V1.1.7(20090323) - fixed the problem in DCD bug. Parani-ESD100&110 V1.0.0 - Support Bluetooth 1.2, DFU, AFH, at+btver?, pairing, faster connection V1.0.1(20061012) - add DCD On/Off option V1.0.2(20061027) - fixed the problem in CSR bug. V1.0.2_shinsung(20061204) - for shinsung inc. connect to msp use pairing signal. V1.1.0(20070326) - add Intercharacter timeout. fixed the problem in toshiba driver bug. fixed the problem in Flowcontol bug. V1.1.1(20070530) - fixed the problem in intercharacter timout. add sniff low power mode. (S47~S52) add ACL connection. (ata) - add reset and pairing pin software pull up. V1.1.2(20070912) - fixed the problem in DCD signal. V1.1.3(20080107) - add S45(iac), pairing iac V1.1.4(20080314) - fixed the problem in DCD signal. support 000b53 bd address. fixed the problem in 28 connection with MSP1000 and SDP response bug. V1.1.5(20080416) - change at+uartconfig, fixed the problem in at+btcancel bug V1.1.6(20090310) - add pairing cod, remove pairing iac V1.1.7(20090323) - fixed the problem in DCD bug. Parani-ESD200&210 V1.0.0 - Support Bluetooth 1.2, DFU, AFH, at+btver?, faster connection V1.0.1(20061002) - fixed the problem in S22 conf. V1.0.2(20061012) - add DCD On/Off option V1.1.0(20070326) - add Intercharacter timeout. fixed the problem in toshiba driver bug. fixed the problem in Flowcontol bug. V1.1.1(20070530) - fixed the problem in intercharacter timout. add sniff low power mode. (S47~S52) add ACL connection. (ata) - add reset pin software pull up. V1.1.2(20070912) - fixed the problem in DCD signal. V1.1.3(20080107) - add S45(iac), pairing iac V1.1.4(20080314) - fixed the problem in DCD signal. support 000b53 bd address. fixed the problem in 28 connection with MSP1000 and SDP response bug. V1.1.5(20080416) - change at+uartconfig, fixed the problem in at+btcancel bug V1.1.7(20090323) - fixed the problem in DCD bug. C02_v1.0.2(20061024) - change DCD signal C02_v1.0.3 (20061027) - fixed the problem in CSR bug. C02_v1.0.4 (20061122) - modified to work like old Promi-ESD02. by connecting the 4th pio to green_led. C02_v1.0.5 (20070418) - fixed for at+uartconfig command to work without hardware flow control option. C02_v1.0.6 (20070807) - modified to work like old Promi-ESD02. by connecting the 4th pio to green_led. Parani-SD200L V1.0.0(20070104) - Model with battery built in. V1.0.2(20070912) - fixed the problem in DCD signal. ------------------------------------------------------Conf_SW--------------------------------------------------------------- ParaniWIN 1.0.1(200607) - fixed to activate / deactivate according to Dip switch status. add function to measure the signal strength. add window for device information. add Connection Wizard function. 1.0.2(20070308) - fixed to support none alpha-numeric character for pin code. 1.0.3(20070912) - rs232 menu(parity, stop bit) disable in dip switch mode. 2.0.1(20080319) - paraniwin(1.0.4), paraniupdater(2.0.1), paraniwizard(1.0.1)(only esd) support 460800, 921600 baudrate for SD/ESD1000 fixed for 300sec scan bug. -------------------------------------------------------Manual------------------------------------------------------------------ Parani-SD 1.1.0 - C.4. S6: fix Enable Low Power Mode (default 0) typo. S23, S26 add intercharacter timeout function. 1.1.2(200705) - add S-register47~52. 1.1.3(20070912) - Update Approval, Command Validity, 3.4 data bit, A.1 voltage, B3.7, remove at+dfu, S23, B3.4, ParaniWIN Dip switch conf. 1.1.4(20080107) - Update pairing button, add S45 1.1.5(20090121) - Update dimension info 1.1.6(20090310) - Update pairing button and add s43,44 Parani-SD_kr 1.1.2(200705) - first release. 1.1.3(20070912) - Update Approval, Command Validity, 3.4 data bit, A.1 voltage, B3.7, remove at+dfu, S23, B3.4, ParaniWIN Dip switch conf. 1.1.4(20080107) - Update pairing button, add S45 1.1.5(20090121) - Update dimension info 1.1.6(20090310) - Update pairing button and add s43,44 Parani-ESD 1.1.0 - C.4. S6: fix Enable Low Power Mode (default 0) typo. S23, S26 add intercharacter timeout function. 1.1.2(200705) - add S-register47~52. 1.1.3(20070912) - Update Approval, Command Validity, 3.4 data bit, A.1 voltage, B3.7, remove at+dfu, S23, B3.4 1.1.4(20080107) - Update pairing button, add S45 1.1.5(20090121) - Update dimension info 1.1.6(20090310) - Update pairing button and add s43,44 Parani-ESD_kr 1.1.2(200705) - first release. 1.1.3(20070912) - Update Approval, Command Validity, 3.4 data bit, A.1 voltage, B3.7, remove at+dfu, S23, B3.4 1.1.4(20080107) - Update pairing button, add S45 1.1.5(20090121) - Update dimension info 1.1.6(20090310) - Update pairing button and add s43,44 CONTACTS ========= Sena Technologies Inc. 210 Yangjae-dong, Seocho-gu Seoul, Korea 137-130 url: http://www.sena.com email: info@sena.com phone: +82-2-573-7772 fax: +82-2-573-7710 Technical support: email: support@sena.com phone: +82-2-573-5422